Incubators - for the Beginner up to the Professional
Incubators (Description / Function / Options) ... Dead-in-Shells (Assessment & Procedures) / Chick Deformities ... Candling Eggs ... Egg Suppliers
Below Information available in English and German languages - German translation "Feuchtigkeit und Belüftung"
Humidity and Ventilation
A well-designed incubator should maintain temperature within 1/4 degree F and humidity within 1 degree F wet bulb temperature.
Short term variations in humidity are not important. The average humidity over the incubation period needs to be near optimum to achieve the ideal weight loss. High humidity for the day or two of hatching is also important. Beware chronic, excessive humidity.
Two factors affect incubation humidity: water evaporation within the cabinet (from eggs as well as from additional water) and levels of ventilation. The water content of the air being drawn through the incubator will also have an effect.
There are two methods available to bird breeders to achieve correct humidity levels in the Octagon 20 Advance Incubator (Note: regulation is more difficult with less sophisticated incubators)
- Monitor humidity levels and adjust to match published guidelines for different species.
Generally accepted incubation RH levels for species groups: During incubation: Poultry 40 – 50 % RH (relative humidity) Waterfowl 45 – 55 % RH Parrots 35 – 45 % RH Hatching All species 65 % RH or more
For more specific information on particular species’ requirements check the relevant literature.
- Monitor egg weight loss which varies as a direct result of humidity and correct against published weight loss figures for the species.
Eggs lose moisture through their shells and the rate of evaporation depends on the humidity levels around the eggs and the shell porosity. During incubation eggs need to lose a fixed amount of water which corresponds to a loss in weight of around 13-16% depending on species. By weighing eggs periodically during incubation it is possible to monitor and, if necessary, correct humidity levels to achieve the correct weight loss.
Weigh the eggs on the day they are set in the incubator, take the average weight and plot this on a graph (see example below). The ideal weight loss line can be plotted by joining the point representing initial average weight with the ideal hatch weight (13-16% less depending on species) with the x-axis representing the incubation period (in days).
By measuring actual average weights every few days the actual weight loss can be plotted and compared to the ideal weight loss line and corrections can be made. For example if the actual weight loss was greater than ideal (see graph below) then the air has been too dry and humidity levels need to be increased to compensate.
Normaler Gewichtsverlust unterschiedlicher Arten: Geflügel 13 % Papageien 16 % Wasservögel 14 %
Of the two methods given above the most reliable is egg weight method and is recommended – particularly where poor hatch rates are experienced or if eggs of high value are being incubated.
Alter the setting of the ventilation control (reduce ventilation to increase humidity) and have water in neither, one or both of the water channels to change the humidity level. Humidity levels may be further increased by placing strips of evaporating card or cloth into one or both of the water troughs (applicable to the Octagon 20 Advance Incubators only - follow the instructions pertaining to the incubator you are using).
In all cases the humidity for hatching needs to be high to prevent the shell membranes to dry out which makes it very difficult and sometimes impossible for the chick to emerge. When they dry out they become like leather.
Because of the short duration involved water/weight loss will not be significantly affected. High humidity is necessary to prevent membranes drying and hardening before the hatch fully emerges. Humidity will naturally increase as the first eggs begin to hatch and internal membranes begin to dry. This effect is in addition to the increased area of water evaporation from the water channels.
During hatching the high humidity levels will fall dramatically when the lid is opened and will take some time to build up. Resist the temptation to lift the lid frequently – leave for at least 6 hours between inspections.
The Advance Humidity Pump is available as an option on the Octagon 20 Advance incubator. The incubator digital control system not only reads the humidity in the incubator but it provides a control signal to operate the water pump and accurately maintain the humidity level at the desired level.
High Quality Species Photos, Videos and/or Articles Contributions are welcome! Click here to upload articles and images.
Please Note: The images on this page are the sole property of the photographers (unless marked as Public Domain). Please contact the photographers directly with respect to any copyright or licensing questions. Thank you.
The Avianweb strives to maintain accurate and up-to-date information; however, mistakes do happen. If you would like to correct or update any of the information, please send us an e-mail. THANK YOU!